Sun Cobalt - Smaller, Bluer, Better, and Free Firmware version 2.10.3-ext3 Current date: Jul 16 01:43:58 UTC 2008 ROM build info: Thu Mar 11 08:51:36 MST 2004 . System serial number: invalid csum! System type: 3000 series system, Version 1 board Silicon serial number: d00000088ff5bb01 Monitor: 153536 bytes Memory: 256 MB CPU: 1 processor(s) detected CPU 0: AuthenticAMD 448MHz (4.5 x 100MHz host bus) [BSP] Initializing flash: done Flash Bank 0: AMD AM29F080B 1024KB (01:d5) Flash Bank 1: not installed. Mounting ROM fs: done Initializing PCI: done Initializing ethernet: 2 controller(s) found Initializing IDE: found ALI M5229 at 00:78 scanning ide0: master scanning ide1: IDE: stabilizing spinup: 100% Checking Memory: done Press spacebar to enter ROM mode Booting default method - From disk First stage kernel (Linux): Decompressing - done ERROR: cannot relocate with filesize 0 Second stage load failed. Booting ROM kernel... Decompressing - done ERROR: cannot relocate with filesize 0 Linux version 2.4.25-ROM (duncan@atherton) (gcc version 3.3.3 (Debian 20040306)) #1 Thu Mar 11 08:47:53 MST 2004 BIOS-provided physical RAM map: BIOS-e801: 0000000000000000 - 000000000009f000 (usable) BIOS-e801: 0000000000100000 - 0000000010000000 (usable) 256MB LOWMEM available. On node 0 totalpages: 65536 zone(0): 4096 pages. zone(1): 61440 pages. zone(2): 0 pages. DMI not present. Kernel command line: console=ttyS0,115200 ip=off Initializing CPU#0 Detected 448.219 MHz processor. Calibrating delay loop... 894.56 BogoMIPS Memory: 257240k/262144k available (1141k kernel code, 4516k reserved, 244k data, 100k init, 0k highmem) Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line) CPU: L2 Cache: 128K (32 bytes/line) CPU: AMD-K6(tm)-III Processor stepping 04 Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: AMD K6 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd VFS: Disk quotas vdquot_6.5.1 Journalled Block Device driver loaded pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10f Non-volatile memory driver v1.2 loop: loaded (max 8 devices) eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others eth0: Invalid EEPROM checksum 0x2233, check settings before activating this device! eth0: PCI device 8086:1209, 00:10:E0:03:53:0E, IRQ 11. Receiver lock-up bug exists -- enabling work-around. Board assembly 000000-000, Physical connectors present: Primary interface chip None PHY #0. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0xdbd8681d). Receiver lock-up workaround activated. eth1: Invalid EEPROM checksum 0x902c, check settings before activating this device! eth1: PCI device 8086:1209, 00:10:E0:03:4C:7C, IRQ 10. Receiver lock-up bug exists -- enabling work-around. Board assembly 000000-000, Physical connectors present: Primary interface chip None PHY #0. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0xdbd8681d). Receiver lock-up workaround activated. Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller at PCI slot 00:0f.0 ALI15X3: chipset revision 193 ALI15X3: 100% native mode on irq 14 ide0: BM-DMA at 0xfdd0-0xfdd7, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xfdd8-0xfddf, BIOS settings: hdc:DMA, hdd:DMA hda: ST320410A, ATA DISK drive ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx blk: queue c0298fa0, I/O limit 4095Mb (mask 0xffffffff) ide0 at 0xfdf8-0xfdff,0xfdf6 on irq 14 hda: attached ide-disk driver. hda: host protected area => 1 hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(33) Partition check: hda: hda1 hda2 md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 613.200 MB/sec 32regs : 350.800 MB/sec pII_mmx : 828.800 MB/sec p5_mmx : 810.000 MB/sec raid5: using function: pII_mmx (828.800 MB/sec) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 32768) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 100k freed INIT: version 2.86 booting mount: wrong fs type, bad option, bad superblock on tmpfs, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so Activating swap. Adding Swap: 1003960k swap-space (priority -1) Checking root file system... fsck 1.37 (21-Mar-2005) /dev/hda1: clean, 13900/2314656 files, 156293/4620288 blocks EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal mount: wrong fs type, bad option, bad superblock on tmpfs, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so System time was Wed Jul 16 01:44:39 UTC 2008. Setting the System Clock using the Hardware Clock as reference... System Clock set. System local time is now Wed Jul 16 01:44:41 UTC 2008. Cleaning up ifupdown...done. Checking all file systems... fsck 1.37 (21-Mar-2005) Setting kernel variables ... ... done. Mounting local filesystems... mount: wrong fs type, bad option, bad superblock on tmpfs, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so Cleaning /tmp /var/run /var/lock. mount: wrong fs type, bad option, bad superblock on tmpfs, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so Running 0dns-down to make sure resolv.conf is ok...done. Setting up networking...done. Setting up IP spoofing protection: rp_filter. Configuring network interfaces...Internet Software Consortium DHCP Client 2.0pl5 Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium. All rights reserved. Please contribute if you find this software useful. For info, please visit http://www.isc.org/dhcp-contrib.html socket: Address family not supported by protocol Make sure to set CONFIG_PACKET=y and CONFIG_FILTER=y in your kernel configuration! exiting. Failed to bring up eth1. done. Setting the System Clock using the Hardware Clock as reference... System Clock set. Local time: Tue Jul 15 20:44:45 CDT 2008 Initializing random number generator...done. Recovering nvi editor sessions... done. INIT: Entering runlevel: 2 Starting system log daemon: syslogd. Starting kernel log daemon: klogd. Starting MTA: exim4. Starting internet superserver: inetd. Starting deferred execution scheduler: atd. Starting periodic command scheduler: cron. Debian GNU/Linux 3.1 cobx1 ttyS0 cobx1 login: -------------------------------------------------------------------------------- Disk /dev/hda: 20.0 GB, 20020396032 bytes 16 heads, 63 sectors/track, 38792 cylinders Units = cylinders of 1008 * 512 = 516096 bytes Device Boot Start End Blocks Id System /dev/hda1 1 1524 768095+ 83 Linux /dev/hda2 1525 1846 162288 5 Extended /dev/hda3 1847 2253 205128 83 Linux /dev/hda4 2254 38792 18415656 83 Linux /dev/hda5 1525 1585 30743+ 83 Linux /dev/hda6 1586 1846 131543+ 82 Linux swap / Solaris #/etc/fstab /dev/hda1 / ext2 defaults 1 1 /dev/hda6 swap swap defaults 0 0 /dev/hda3 /var ext2 defaults,nosuid 2 2 /dev/hda4 /home ext2 defaults,usrquota,grpquota,grpid 3 3 none /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=0622 0 0 -------------------------------------------------------------------------------- [root /etc]# cat inittab # # inittab This file describes how the INIT process should set up # the system in a certain run-level. # # Author: Miquel van Smoorenburg, <miquels@drinkel.nl.mugnet.org> # Modified for RHS Linux by Marc Ewing and Donnie Barnes # Modified for Cobalt Linux by Duncan Laurie et. all # # Default runlevel. The runlevels used by RHS are: # 0 - halt (Do NOT set initdefault to this) # 1 - Single user mode # 2 - Multiuser, without NFS (The same as 3, if you do not have networking) # 3 - Full multiuser mode # 4 - unused # 5 - X11 # 6 - reboot (Do NOT set initdefault to this) # id:3:initdefault: # System initialization. si::sysinit:/etc/rc.d/rc.sysinit l0:0:wait:/etc/rc.d/rc 0 l1:1:wait:/etc/rc.d/rc 1 l2:2:wait:/etc/rc.d/rc 2 l3:3:wait:/etc/rc.d/rc 3 l4:4:wait:/etc/rc.d/rc 4 l5:5:wait:/etc/rc.d/rc 5 l6:6:wait:/etc/rc.d/rc 6 # Things to run in every runlevel. ud::once:/sbin/update # Trap CTRL-ALT-DELETE ca::ctrlaltdel:/sbin/shutdown -t3 -r now # When our UPS tells us power has failed, assume we have a few minutes # of power left. Schedule a shutdown for 2 minutes from now. # This does, of course, assume you have powerd installed and your # UPS connected and working correctly. pf::powerfail:/sbin/shutdown -f -h +2 "Power Failure; System Shutting Down" # If power was restored before the shutdown kicked in, cancel it. pr:12345:powerokwait:/sbin/shutdown -c "Power Restored; Shutdown Cancelled" # serial console port 1:12345:respawn:/sbin/getty ttyS0 115200 #2:2345:respawn:/sbin/mingetty tty2 #3:2345:respawn:/sbin/mingetty tty3 #4:2345:respawn:/sbin/mingetty tty4 #5:2345:respawn:/sbin/mingetty tty5 #6:2345:respawn:/sbin/mingetty tty6 # Run xdm in runlevel 5 x:5:respawn:/usr/bin/X11/xdm -nodaemon -------------------------------------------------------------------------------- [root /etc]# lsmod Module Size Used by eepro100 19008 2 (autoclean) bwmgmt 22144 1 (autoclean) [root /etc]# cat /etc/modules.conf # for the Cobalt Bandwidth Manager alias bandwidth_mgr bwmgmt alias eth0 eepro100 alias eth1 eepro100 -------------------------------------------------------------------------------- debian:/proc# lspci 0000:00:00.0 Host bridge: ALi Corporation M1541 (rev 04) 0000:00:01.0 PCI bridge: ALi Corporation M1541 PCI to AGP Controller (rev 04) 0000:00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 0000:00:03.0 Non-VGA unclassified device: ALi Corporation M7101 Power Management Controller [PMU] 0000:00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] (r ev c3) 0000:00:0e.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 04) 0000:00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c1) 0000:00:10.0 Ethernet controller: Intel Corp. 82559ER (rev 09) 0000:00:12.0 Ethernet controller: Intel Corp. 82559ER (rev 09) -------------------------------------------------------------------------------- Cobalt Linux release 6.0 (Shinkansen-Decaf) Kernel 2.2.16C32_III on an i586 [root /root]# dmesg Linux version 2.2.16C32_III (root@sun.cobalt.com) (gcc version egcs-2.91.66 1999 0314/Linux (egcs-1.1.2 release)) #1 Fri Nov 9 21:54:54 PST 2001 Ignoring bogus EBDA pointer 3FFF000 Detected 448220 kHz processor. Pending 0x00 Calibrating delay loop... 894.57 BogoMIPS Memory: 257496k/262144k available (1244k kernel code, 416k reserved, 2924k data, 64k init) Dentry hash table entries: 32768 (order 6, 256k) Buffer cache hash table entries: 262144 (order 8, 1024k) Page cache hash table entries: 65536 (order 6, 256k) VFS: Diskquotas version dquot_6.4.0 initialized CPU: L1 I Cache: 32K L1 D Cache: 32K CPU: L2 Cache: 128K CPU: AMD AMD-K6(tm)-III Processor stepping 04 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP TCP: Hash tables configured (ehash 262144 bhash 65536) Initializing RT netlink socket Starting kswapd v 1.5 Cobalt watchdog v1.4 enabled Cobalt I2C bus initialized Cobalt temperature sensor v1.3 enabled Serial driver version 4.27 with<4>keyboard: Timeout - AT keyboard not present? keyboard: Timeout - AT keyboard not present? no serial options enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configured Real Time Clock Driver v1.09 lcd: Cobalt LCD Driver v3.12 serialnumber: Version 1.9 initialized. Serial number=d00000088ff5bb01. Copyright (c)1994-2000 Axent Technologies, Inc. Uniform Multi-Platform E-IDE driver Revision: 6.30 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller on PCI bus 00 dev 78 ALI15X3: chipset revision 193 ALI15X3: 100% native mode on irq 14 ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA hda: ST320410A, SN=6FG0RP7K, FWREV=3.34, ATA DISK drive ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ST320410A, 19092MB w/2048kB Cache, CHS=38792/16/63, UDMA(33) md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12 translucent personality registered linear personality registered raid0 personality registered raid1 personality registered raid5 personality registered raid5: measuring checksumming speed raid5: MMX detected, trying high-speed MMX checksum routines pII_mmx : 933.069 MB/sec p5_mmx : 862.203 MB/sec 8regs : 438.912 MB/sec 32regs : 281.178 MB/sec using fastest function: pII_mmx (933.069 MB/sec) sym53c8xx: at PCI bus 0, device 14, function 0 sym53c8xx: 53c875 detected sym53c875-0: rev 0x4 on pci bus 0 device 14 function 0 irq 12 sym53c875-0: ID 7, Fast-20, Parity Checking scsi0 : sym53c8xx-1.7.3a-20010304 scsi : 1 host. scsi : detected total. md.c: sizeof(mdp_super_t) = 4096 Partition check: hda: hda1 hda2 < hda5 hda6 > hda3 hda4 autodetecting RAID arrays autorun ... ... autorun DONE. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 64k freed Adding Swap: 131532k swap-space (priority -1) Cobalt Networks Bandwidth Limiting Module Copyright (c) 1999, Cobalt Networks, Inc. All rights reserved eth0: Invalid EEPROM checksum 0x2233, check settings before activating this devi ce! eth0: Intel PCI EtherExpress Pro100 82559ER, 00:10:E0:03:53:0E, I/O at 0x6200, I RQ 11. Board assembly 000000-000, Physical connectors present: Primary interface chip None PHY #0. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0xdbd8681d). Receiver lock-up workaround activated. eth1: Invalid EEPROM checksum 0x902c, check settings before activating this devi ce! eth1: Intel PCI EtherExpress Pro100 82559ER, 00:10:E0:03:4C:7C, I/O at 0x6240, I RQ 10. Board assembly 000000-000, Physical connectors present: Primary interface chip None PHY #0. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0xdbd8681d). Receiver lock-up workaround activated. portmap: RPC call returned error 111 RPC: task of released request still queued! RPC: (task is on xprt_pending) portmap: RPC call returned error 111 RPC: task of released request still queued! RPC: (task is on xprt_pending) lockd_up: makesock failed, error=-111 portmap: RPC call returned error 111 RPC: task of released request still queued! RPC: (task is on xprt_pending) -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- --------------------------------------------------------------------------------